Combat Fixed Blade Knife

Fallkniven A1xb Tungsten Carbide Knife

- Made by Fällkniven -

Introduction:

Your X-knife is the strongest, sharpest and safest stainless steel knife in production. If your life is in danger, you can always rely on your X-knife. It is designed to withstand all the stresses applied by the human hand, which means that it is virtually indestructible. It assumes, however, that you are careful with the knife and that it is used  as intended, namely as a sharp precision tool. The basis of the X-knife’s strength lies in the laminated cobalt steel, and also in the well-thought-out construction in which break zones have been eliminated. Together with the hand-shaped convex edge, the X-knife is a concept that beats everything else in the world in terms of safety and comfort. About the all-black version: This surface is the hardest we have ever encountered. Although we really tried to wear down the black coating with the toughest, driest curly birch we could find, we never succeeded in getting holes in this extremely hard, durable surface. Still, we cannot guarantee that it will stay for time and eternity, after all, the blade can be ground and certainly a diamond or ceramic stone will bite on the surface. Also for example a grain of sand can scratch or leave a mark in the coating. The hardness is at 2400 HV (Vickers) or around HRC 83.

In their usual way, they have put a lot of energy into designing a safe knife sheath, which is actually where the knife will spend most of its time. The design of the sheath determines the access to the knife, and here they have really put all their efforts in order to get a safe sheath that allows easy access to the knife. The sheath has both a transport lock (the folding bracket with a strap) and a working safety detail that allows the knife to be in place until you decide to use it. It is a bit a belt-and-braces approach, but we like putting safety first – a lost knife is of no use. The transport lock will therefore allow the knife to be fastened tip-up or tip-down on the body or on your equipment without any risk.

Specifications:

Steel: Laminated CoS HRC 60
Blade length: 6.34" inch / 161 mm
Total length: 11.18” inch / 284 mm
Handle length: 4.84” inch / 123 mm
Handle scales: Thermorun

Blade thickness: 7 mm
Knife weight 401 gr.

Additional Information:

Edge: Convex

Sheath Included: Zytel

Handle: Lanyard Hole

Tang: Full Tang

Blade: Tungsten Carbide

Laminated CoS: A newly developed high alloy cobalt-special steel

Fallkniven A1bL Survival Knife

- Made by Fällkniven -

Introduction:

A new world standard was set with the Fallkniven A1 through attention to important details including technical design, ergonomics and economy. The Fallkniven A1 surpasses international standards for strength, personal security capabilities, and value for money. The Fallkniven A1 is an all-purpose knife on the larger side designed for heavy duty use. The powerful blade is made of extremely hard and tough laminated VG10 steel, and will withstand the stress of hard use. The knife is superb at chopping as well finer daily cutting tasks thanks to the ergonomic grip. The full tang goes entirely through the handle so you can strike with the end of it without breaking the grip. The sturdy black leather sheath allows you to fasten the knife on your belt or your pack, and even upside down. The Fallkniven A1 is unaffected by water and works equally well in extreme cold and stifling heat. If your needs require that no reflections come from your knife blade, we offer a black CeraKote option. The CeraKote is an extremely tough surface coating that will also protect the blade from corrosion. CeraKote is a hard coating made of Teflon and ceramics that we apply for military users and others who want to avoid shiny blades. Be aware, however, that although CeraKote is an industry standard, it is also just a finish applied to the metal blade similar to painting a car. Please note that physical abrasions could scratch through the CeraKote coating. Over time, the black CeraKote may separate from the blade, but more durable coatings make the knife difficult to sharpen and cost up to 100 times more than CeraKote.

Attaching a black surface on a rust resistant, perfectly smooth blade so that it sticks for time and eternity is all impossible. We have tested some extremely hard coatings, but they proved to be many times more expensive and make it harder to sharpen the knife.

Specifications:

Steel: Laminated VG10 HRC 59

Blade length: 6.30" inch / 160 mm
Total length: 11.02” inch / 280 mm
Handle length: 4.72” inch / 120 mm
Handle scales: Kraton

Blade thickness: 6 mm
Knife weight 319 gr.

Additional Information:

Edge: Convex

Sheath Included: Leather

Handle: Lanyard Hole

Tang: Protruding Broad Tang

Blade: Black Coated

VG10: A well known high alloy molybdenum/cobalt steel

Fallkniven A1bz Survival Knife

- Made by Fällkniven -

Introduction:

A new world standard was set with the Fallkniven A1 through attention to important details including technical design, ergonomics and economy. The Fallkniven A1 surpasses international standards for strength, personal security capabilities, and value for money. The Fallkniven A1 is an all-purpose knife on the larger side designed for heavy duty use. The powerful blade is made of extremely hard and tough laminated VG10 steel, and will withstand the stress of hard use. The knife is superb at chopping as well finer daily cutting tasks thanks to the ergonomic grip. The full tang goes entirely through the handle so you can strike with the end of it without breaking the grip. The sturdy black leather sheath allows you to fasten the knife on your belt or your pack, and even upside down. The Fallkniven A1 is unaffected by water and works equally well in extreme cold and stifling heat. If your needs require that no reflections come from your knife blade, we offer a black CeraKote option. The CeraKote is an extremely tough surface coating that will also protect the blade from corrosion. CeraKote is a hard coating made of Teflon and ceramics that we apply for military users and others who want to avoid shiny blades. Be aware, however, that although CeraKote is an industry standard, it is also just a finish applied to the metal blade similar to painting a car. Please note that physical abrasions could scratch through the CeraKote coating. Over time, the black CeraKote may separate from the blade, but more durable coatings make the knife difficult to sharpen and cost up to 100 times more than CeraKote.

Attaching a black surface on a rust resistant, perfectly smooth blade so that it sticks for time and eternity is all impossible. We have tested some extremely hard coatings, but they proved to be many times more expensive and make it harder to sharpen the knife.

Specifications:

Steel: Laminated VG10 HRC 59

Blade length: 6.30" inch / 160 mm
Total length: 11.02” inch / 280 mm
Handle length: 4.72” inch / 120 mm
Handle scales: Kraton

Blade thickness: 6 mm
Knife weight 319 gr.

Additional Information:

Edge: Convex

Sheath Included: Zytel

Handle: Lanyard Hole

Tang: Protruding Broad Tang

Blade: Black Coated

VG10: A well known high alloy molybdenum/cobalt steel