Army Knives

Muela Scorpion-19N Combat Knife

- Handcrafted by Muela in Spain -

This is a ruggedly made tactical combat knife. The high leather sheath is included & belongs to this impressive knife. Guard black "Zamak".

Specifications:

Steel: 420H stainless steel blade (High Carbon contents)

PTFE Anti Corrosion Coating / Rockwell: 54-58 HRC

Blade length: 7.086” inch / 180 mm
Total length: 12.204” inch /  310 mm
Handle length: 5.118” inch / 130 mm
Handle scales: Non Slip Rubber
Blade thickness: 4 mm
Knife weight 350 gr.

– Lanyard hole for Safety Cord

FOX FKMD Leonida FX-0171106 Military Knife

- Made by Fox Knives in Italy -

Design by: "FOX Knives".

Introduction:

Sheath NYLON 1000D with MOLLE system and FRN (NYLON reinforced fiberglass) plate with wire cutting plate and sharpening stone.

Specifications:

Steel: N690-Co stainless steel HRC 58-60
Blade length: 7.28" inch / 185 mm
Total length: 12.20” inch / 310 mm
Handle length: 4.92” inch / 125 mm
Handle scales: FORPRENE® OD green

Blade thickness: 5 mm
Overall weight 285 gr.

Additional Information:

Blade Coating: Black Idroglider  

Blade: Partially Serrated Blade with saw on the Spine

Blade: Wire Cutting Plate

Sheath: NYLON 1000D with MOLLE system and FRN ®(NYLON reinforced fiberglass)
with stainless steel wire cutting plate and sharpening stone

Idroglider
Special non stick coating made of PTFE that ensures long life and rust resistance.

Muela Scorpion-18NM Combat Knife

- Handcrafted by Muela in Spain -

This is a ruggedly made tactical combat knife. The high Quality Desert Camo sheath is included & belongs to this impressive knife. Guard black "Zamak".

Specifications:

Steel: 420H stainless steel blade (High Carbon contents)

PTFE Anti Corrosion Coating / Rockwell: 54-58 HRC

Blade length: 7.086” inch / 180 mm
Total length: 12.204” inch /  310 mm
Handle length: 5.118” inch / 130 mm
Handle scales: Non Slip Rubber
Blade thickness: 4 mm
Knife weight 350 gr.

– Lanyard hole for Safety Cord

FOX FKMD Leonida FX-0171107 Military Knife

- Made by Fox Knives in Italy -

Design by: "FOX Knives".

Introduction:

Sheath NYLON 1000D with MOLLE system and FRN (NYLON reinforced fiberglass) plate with wire cutting plate and sharpening stone.

Specifications:

Steel: N690-Co stainless steel HRC 58-60
Blade length: 7.28" inch / 185 mm
Total length: 12.20” inch / 310 mm
Handle length: 4.92” inch / 125 mm
Handle scales: FORPRENE® black

Blade thickness: 5 mm
Overall weight 285 gr.

Additional Information:

Blade Coating: Black Idroglider  

Blade: Partially Serrated Blade

Blade: Wire Cutting Plate

Sheath: NYLON 1000D with MOLLE system and FRN ®(NYLON reinforced fiberglass)
with stainless steel wire cutting plate and sharpening stone

Idroglider
Special non stick coating made of PTFE that ensures long life and rust resistance.

Fallkniven A1xb Tungsten Carbide Knife

- Made by Fällkniven -

Introduction:

Your X-knife is the strongest, sharpest and safest stainless steel knife in production. If your life is in danger, you can always rely on your X-knife. It is designed to withstand all the stresses applied by the human hand, which means that it is virtually indestructible. It assumes, however, that you are careful with the knife and that it is used  as intended, namely as a sharp precision tool. The basis of the X-knife’s strength lies in the laminated cobalt steel, and also in the well-thought-out construction in which break zones have been eliminated. Together with the hand-shaped convex edge, the X-knife is a concept that beats everything else in the world in terms of safety and comfort. About the all-black version: This surface is the hardest we have ever encountered. Although we really tried to wear down the black coating with the toughest, driest curly birch we could find, we never succeeded in getting holes in this extremely hard, durable surface. Still, we cannot guarantee that it will stay for time and eternity, after all, the blade can be ground and certainly a diamond or ceramic stone will bite on the surface. Also for example a grain of sand can scratch or leave a mark in the coating. The hardness is at 2400 HV (Vickers) or around HRC 83.

In their usual way, they have put a lot of energy into designing a safe knife sheath, which is actually where the knife will spend most of its time. The design of the sheath determines the access to the knife, and here they have really put all their efforts in order to get a safe sheath that allows easy access to the knife. The sheath has both a transport lock (the folding bracket with a strap) and a working safety detail that allows the knife to be in place until you decide to use it. It is a bit a belt-and-braces approach, but we like putting safety first – a lost knife is of no use. The transport lock will therefore allow the knife to be fastened tip-up or tip-down on the body or on your equipment without any risk.

Specifications:

Steel: Laminated CoS HRC 60
Blade length: 6.34" inch / 161 mm
Total length: 11.18” inch / 284 mm
Handle length: 4.84” inch / 123 mm
Handle scales: Thermorun

Blade thickness: 7 mm
Knife weight 401 gr.

Additional Information:

Edge: Convex

Sheath Included: Zytel

Handle: Lanyard Hole

Tang: Full Tang

Blade: Tungsten Carbide

Laminated CoS: A newly developed high alloy cobalt-special steel

Fallkniven A1xbclip Survival Knife

- Made by Fällkniven -

Introduction:

Your X-knife is the strongest, sharpest and safest stainless steel knife in production. If your life is in danger, you can always rely on your X-knife. It is designed to withstand all the stresses applied by the human hand, which means that it is virtually indestructible. It assumes, however, that you are careful with the knife and that it is used  as intended, namely as a sharp precision tool.

The basis of the X-knife’s strength lies in the laminated cobalt steel, and also in the well-thought-out construction in which break zones have been eliminated. Together with the hand-shaped convex edge, the X-knife is a concept that beats everything else in the world in terms of safety and comfort.

In their usual way, they have put a lot of energy into designing a safe knife sheath, which is actually where the knife will spend most of its time. The design of the sheath determines the access to the knife, and here they have really put all their efforts in order to get a safe sheath that allows easy access to the knife. The sheath has both a transport lock (the folding bracket with a strap) and a working safety detail that allows the knife to be in place until you decide to use it. It is a bit a belt-and-braces approach, but we like putting safety first – a lost knife is of no use. The transport lock will therefore allow the knife to be fastened tip-up or tip-down on the body or on your equipment without any risk.

This knife sheath has a stainless clip that allows you to easily carry the knife on your waist belt. The advantages are several – including that you can easily remove and stow your knife. When belt-mounted, the knife will hang vertically, a few centimeters lower than the belt, allowing it to be accessed even if wearing a backpack or long jacket. The articulation in this sheath system allows the wearer to move the knife and sheath to one side when seated or driving a vehicle.

Specifications:

Steel: Laminated CoS HRC 60
Blade length: 6.34" inch / 161 mm
Total length: 11.18” inch / 284 mm
Handle length: 4.84” inch / 123 mm
Handle scales: Thermorun

Blade thickness: 7 mm
Knife weight 401 gr.

Additional Information:

Edge: Convex

Sheath Included: Zytel

Handle: Lanyard Hole

Tang: Full Tang

Blade: Satin Finish

Laminated CoS: A newly developed high alloy cobalt-special steel

Fallkniven A1x Military Survival Knife

- Made by Fällkniven -

Introduction:

Your X-knife is the strongest, sharpest and safest stainless steel knife in production. If your life is in danger, you can always rely on your X-knife. It is designed to withstand all the stresses applied by the human hand, which means that it is virtually indestructible. It assumes, however, that you are careful with the knife and that it is used  as intended, namely as a sharp precision tool.

The basis of the X-knife’s strength lies in the laminated cobalt steel, and also in the well-thought-out construction in which break zones have been eliminated. Together with the hand-shaped convex edge, the X-knife is a concept that beats everything else in the world in terms of safety and comfort.

In their usual way, they have put a lot of energy into designing a safe knife sheath, which is actually where the knife will spend most of its time. The design of the sheath determines the access to the knife, and here they have really put all their efforts in order to get a safe sheath that allows easy access to the knife. The sheath has both a transport lock (the folding bracket with a strap) and a working safety detail that allows the knife to be in place until you decide to use it. It is a bit a belt-and-braces approach, but we like putting safety first – a lost knife is of no use. The transport lock will therefore allow the knife to be fastened tip-up or tip-down on the body or on your equipment without any risk.

Specifications:

Steel: Laminated CoS HRC 60
Blade length: 6.34" inch / 161 mm
Total length: 11.18” inch / 284 mm
Handle length: 4.84” inch / 123 mm
Handle scales: Thermorun

Blade thickness: 7 mm
Knife weight 401 gr.

Additional Information:

Edge: Convex

Sheath Included: Zytel

Handle: Lanyard Hole

Tang: Full Tang

Blade: Satin Finish

Laminated CoS: A newly developed high alloy cobalt-special steel

Fallkniven A1pro Pilot Survival Knife

- Made by Fällkniven -

Introduction:

There are basic survival knives, and there are survival knives for the professional. Our original models of the F1, S1 and A1 have provided exceptional service for more than 20 years. And due to their outstanding quality and durability they will continue to perform for many more years. Nevertheless our drive to continually improve our knives has led us to develop the new Pro Series. The Pro Series are survival knives of near-unimaginable quality, durability and performance. Compared to their predecessors, the Pro series of F1, S1 and A1 differs in the following important areas:

1. The original laminated VG10 steel is upgraded to a laminate cobalt steel (lam. CoS) blade that ensures a durable edge and improved edge retention.
2. The blades are thicker increasing the torsional rigidity so the knives will withstand even greater external forces.
3. The full-length tapered tang is wider and thicker and therefore significantly stronger.
4. The crossguard is now made of stainless steel and permanently welded to the tang.
5. The convex blade edge has been refined to improve its cutting properties.
6. The zytel sheaths are redesigned, more durable, and better suited for the Molle attachment system.

Understandably these knives fall into a higher price category. However, considering the unparalleled quality they are by no means over priced. A professional survival knife must perform in all weather with no exceptions. The professional survival knife must be comfortable and safe to handle for both fine and rough work in summer heat and winter cold. We at Fallkniven have considered every design aspect of these superb professional survival knives and we stand behind them with a lifetime warranty on materials and workmanship.

Steel: Laminated CoS HRC 60
Blade length: 6.30" inch / 160 mm
Total length: 11.14” inch / 283 mm
Handle length: 4.84” inch / 123 mm
Handle scales: Thermorun

Blade thickness: 7 mm
Knife weight 363 gr.

Additional Information:

Edge: Convex

Sheath Included: Zytel

Handle: Lanyard Hole

Tang: Protruding Broad Tang

Finger Guard: Stainless Steel

Laminated CoS: A newly developed high alloy cobalt-special steel